Pursuit (Audiovox) Alarm System

[Andrew]

Hello

I have an old Audiovox Alarm system installed on my '90 535i. I am pretty sure that it was installed by the dealer when new. I believe that it's model is "Pursuit PRO-9144." (BTW, it is pretty much useless, but I would ike to fool around with it just for fun...)

I am wondering if anyone has any experience with this alarm. If so, is there a setup / configuration mode? I have the original OWNERS manuals for the alarm- there are two SEPARATE manuals: one for "passive operation" and another for "active operation." I believe the installation manual explains how to switch between the modes, but I do not have this information.

There must be a way to program new remotes too, but once again, the information in the manuals does not address it.

I should probably install a new alarm, but if anyone by some strange chance knows anything about this alarm, please let me know.

Thanks!
Andrew

[talltorontoguy]

Here's what I found on the internet, hope this helps...

http://www.autotechs.com/items/item299.htm

Audiovox - Prestige - Pursuit - PRO - Programming

PROGRAMMING TRANSMITTERS:

It is important to remember that during programming, each individual step of the procedure must be executed within 15 seconds of the previous step. When the 15 second time limit is allowed to expire, the system will automatically exit program mode. This is indicated by a long "chirp" from the siren. Additionally, any time the ignition key is turned off while programming, the system will immediately exit program mode. This is also indicated by a long "chirp" from the siren.

TO PROGRAM ADDITIONAL TRANSMITTERS:

I. Enter the vehicle, and turn the ignition key to the "on" position.<br>

2. Move the valet/bypass switch on - off - on - off- on then off.<br>

3. The dash L.E.D. will flash one time, and the siren will "chirp" one time, indicating thesystem is ready to accept programming for channel 1, or the arm/disarm and panic functions.

4. You can assign any of the three transmitter button functions listed below to channel 1.&nbsp;
a) Pressing button #1 on the keychain transmitter.
b) Pressing button #2 on the keychain transmitter.
c) Pressing both buttons simultaneously on the keychain transmitter.

5 Press and hold the selected choice a, b, or c above, until the siren emits a long "chirp" to confirm that programming of channel I was successful.

6. Move the valet/bypass switch on, then off again.

7. The dash mounted L. E. D. will flash 2 times, and the siren will "chirp" one time, indicating that the system is ready to accept programming for channel 2, or the pulsed ground output for remote trunk release, remote car starter, etc.

8. You can assign anyone of the two remaining button functions listed in 4a, 4b, or 4c above to operate channel 2. You cannot use the button(s) that operate channel 1, selected in step 5, to operate channel 2.

9. Press and hold the selected choice. The siren will emit a long "chirp" to confirm that programming of channel 2 was successful.

10. Move the valet/bypass switch on, then off again.

11. The dash mounted L.E.D. will flash 3 times, and the siren will "chirp" one time, indicating that the system is ready to accept programming for channel 3.&nbsp

12. Press and hold the remaining transmitter button function. The siren will emit a long "chirp" to confirm that programming of channel 3 was successful.

13. To exit program mode, either turn the ignition key to the off position, or move the valet switch on then off one additional time. This is indicated by a long "chirp" from the siren.

QUICK REFERENCE:
You can program any individual channel, without reprogramming all channels, by following the quick reference chart below.

CHANNEL VALET SWITCH L.E.D.
1) ON then OFF 3 Times I Flashes
2) ON then OFF 4 Times 2 Flashes
3)) ON then OFF 5 Times 3 Flashes&nbsp;
After the desired channel is programmed, turn the ignition key to the off position to exit programming mode.

[Andrew]

Thanks for the information, but I am afraid that this did not work. (This seems to apply to the newer models...mine must be 14 years old by now.) I think I am just going to install a new one.

Andrew


Here's what I found on the internet, hope this helps...

http://www.autotechs.com/items/item299.htm

Audiovox - Prestige - Pursuit - PRO - Programming

PROGRAMMING TRANSMITTERS:

It is important to remember that during programming, each individual step of the procedure must be executed within 15 seconds of the previous step. When the 15 second time limit is allowed to expire, the system will automatically exit program mode. This is indicated by a long "chirp" from the siren. Additionally, any time the ignition key is turned off while programming, the system will immediately exit program mode. This is also indicated by a long "chirp" from the siren.

TO PROGRAM ADDITIONAL TRANSMITTERS:

I. Enter the vehicle, and turn the ignition key to the "on" position.<br>

2. Move the valet/bypass switch on - off - on - off- on then off.<br>

3. The dash L.E.D. will flash one time, and the siren will "chirp" one time, indicating thesystem is ready to accept programming for channel 1, or the arm/disarm and panic functions.

4. You can assign any of the three transmitter button functions listed below to channel 1.&nbsp;
a) Pressing button #1 on the keychain transmitter.
b) Pressing button #2 on the keychain transmitter.
c) Pressing both buttons simultaneously on the keychain transmitter.

5 Press and hold the selected choice a, b, or c above, until the siren emits a long "chirp" to confirm that programming of channel I was successful.

6. Move the valet/bypass switch on, then off again.

7. The dash mounted L. E. D. will flash 2 times, and the siren will "chirp" one time, indicating that the system is ready to accept programming for channel 2, or the pulsed ground output for remote trunk release, remote car starter, etc.

8. You can assign anyone of the two remaining button functions listed in 4a, 4b, or 4c above to operate channel 2. You cannot use the button(s) that operate channel 1, selected in step 5, to operate channel 2.

9. Press and hold the selected choice. The siren will emit a long "chirp" to confirm that programming of channel 2 was successful.

10. Move the valet/bypass switch on, then off again.

11. The dash mounted L.E.D. will flash 3 times, and the siren will "chirp" one time, indicating that the system is ready to accept programming for channel 3.&nbsp

12. Press and hold the remaining transmitter button function. The siren will emit a long "chirp" to confirm that programming of channel 3 was successful.

13. To exit program mode, either turn the ignition key to the off position, or move the valet switch on then off one additional time. This is indicated by a long "chirp" from the siren.

QUICK REFERENCE:
You can program any individual channel, without reprogramming all channels, by following the quick reference chart below.

CHANNEL VALET SWITCH L.E.D.
1) ON then OFF 3 Times I Flashes
2) ON then OFF 4 Times 2 Flashes
3)) ON then OFF 5 Times 3 Flashes&nbsp;
After the desired channel is programmed, turn the ignition key to the off position to exit programming mode.