Is there a site describing the door handle seal job?

[Jehu]

The one Shogun posted a while back in Japanese wasn't coming up and i just scored a set located in Pittsburgh,PA for $21.00 shipped!

[Blitzkrieg Bob]

http://infinitier.ddo.jp/e32/page/mainte/mainte_50702.htm

[Jehu]

Thanks.

[HIe34]

http://infinitier.ddo.jp/e32/page/mainte/mainte_50702.htm

Bigger holes go in the front
Bigger holes go in the front
Bigger holes go in the front

[Blitzkrieg Bob]

Bigger holes go in the front
Bigger holes go in the front
Bigger holes go in the front


easier to put these gaskets on....And it's too far to his house for me to drive over to help.

[dennyg]

I also need to buy a set. The ones on the Malaysian site are twenty four bucks plus shipping. Does your source have any more for sale?

[Jehu]

I also need to buy a set. The ones on the Malaysian site are twenty four bucks plus shipping. Does your source have any more for sale?

He doesn't appear to.Here are his other items (http://motors.search.ebay.com/_W0QQsassZmbuntain)

and what i got (http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&viewitem=&item=140072319673)

[shogun]

No, that is another one in the link above. Here is the one from Kenneth Woo in Malaysia
http://cgi.ebay.com/ebaymotors/BMW-E32-E34-E36-Z3-Outer-Door-Handle-Rubber-Seals_W0QQcmdZViewItemQQcategoryZ33642QQihZ004QQit emZ140069657573QQrdZ1QQsspagenameZWDVW

Just yesterday I ordered another 30 sets from him, so maybe he is out of stock now ;)

[95///M3]

What the ****... I installed these today and my front door pulls are now hitting the surrounding trim when you pull up on them?!

[Blitzkrieg Bob]

on the to cover?

All the way around the edges, all those pins

[95///M3]

on the to cover?

All the way around the edges, all those pins

Yeah, just like the rears. For some reason both fronts are dragging when opening however. Any other suggestions?

[Blitzkrieg Bob]

and make it move?

Try pushing against the cover and pulling one the locking slide.

This may bring the cover in tighter.

[BigKriss]

I still don't know how to install mine :(

[shogun]

10 minutes job
http://forums.bimmerforums.com/forum/showthread.php?t=232798

http://www.bmw4life.com/doorHandle.htm

[dennyg]

Thanks guys I bought the set tonight from Malaysia.....Would have been nice to save the ten bucks like Jehu did......Instructions from Shogun looks easy enough. Maybe after I install I can spray with high pressure hose without fear of water leaking in doors.

[shogun]

It helps fitting when you heat them up a bit in warm/hot water so that they are more flexible, that helps especially in winter time.

[Paul in NZ]

I had to loosen the torx bolts and reposition the handles a fraction lower to stop the handle rubbing on the trim.It only needs to move a fraction.Kriss if i can do it anyone can...

[Jehu]

Thanks guys I bought the set tonight from Malaysia.....Would have been nice to save the ten bucks like Jehu did......Instructions from Shogun looks easy enough. Maybe after I install I can spray with high pressure hose without fear of water leaking in doors.

I only found those because i looked.I simply type "bmw e34" into the ebay search usually once a day and set its search parameter to "newly listed" and whamo .Most of the stuff there seems to be more of the same all the time lke new Roundells ,tire valve stem caps or Aluminum Pedal sets but now and then something worthwhile shows up.