PDA

View Full Version : 32mm blues...


patznu
03-16-2007, 06:17 PM
Finally I located this mysterious tool, well looking forward to purchasing a bike wrench from bicycle repair shop, made from a company named park $14.99. Question is ...'How difficult will the job be to remove clutch fan and water pump?' 'Will additional tool be needed?' Any and all help would be greatly appreciated!
Blitzkrieg Bob
03-16-2007, 06:31 PM
get a strip of metal 3 or 4mm thick 400mm long 40 to 50mm wide, drill a 12++ mm hole at one corner to fit a pulley nut, and grind a concave from the edge where the hole is back 30mm to allow for the 32mm nut to clear.

this makes it a lot easier to break the nut loose.

Remember it's righty loosey for the 32mm fan nut
patznu
03-17-2007, 02:41 PM
get a strip of metal 3 or 4mm thick 400mm long 40 to 50mm wide, drill a 12++ mm hole at one corner to fit a pulley nut, and grind a concave from the edge where the hole is back 30mm to allow for the 32mm nut to clear.

this makes it a lot easier to break the nut loose.

Remember it's righty loosey for the 32mm fan nut


Well Bob, first thank you very much. Yes you were correct to state the need for this pulley holder but I don't exactly have tools for metal fabrication. Would know anything about this wrench set for rent from advanced autozone There claims to be a pulley holder in this set, but will it fit?
E34-520iSE
03-17-2007, 05:09 PM
Well Bob, first thank you very much. Yes you were correct to state the need for this pulley holder but I don't exactly have tools for metal fabrication. Would know anything about this wrench set for rent from advanced autozone There claims to be a pulley holder in this set, but will it fit?

I guess I'm just a Luddite. My way of removing fan clutches involves a chisel and two or three bops in a clockwise direction with a heavy hammer. Never fails!

Best of luck,

Shaun M
nizmainiac
03-17-2007, 05:54 PM
on my m20 i take out 2 of the bolts on the pulley to give me enough room to use 2 pairs of bigass water pump pliers against each other so there's no to use chisels or anything like that:)
patznu
03-17-2007, 06:38 PM
on my m20 i take out 2 of the bolts on the pulley to give me enough room to use 2 pairs of bigass water pump pliers against each other so there's no to use chisels or anything like that:)


Advanced Autozone did come thru this time with a rent a tool set (36mm wrench and pulley holder 19.00)

So far so good... about to now pull distrib. cap .. then cross bar per Bentley.
patznu
03-18-2007, 12:20 PM
Advanced Autozone did come thru this time with a rent a tool set (36mm wrench and pulley holder 19.00)

So far so good... about to now pull distrib. cap .. then cross bar per Bentley.
Well after one lost extension, a cracked distributor cap, a never finding bolt to the replacing of cross bar/hose, the objective was met. Coolant pump replaced. Several things achieved; cabin area now receives heat, car no longer overheats nor overflows at area of pump. Strange but content with a quieter start...like smoother? I also should mention that the old pump was quite disintergrated, as the forum warns, in result I took heed and purchased the correct one with metal impel.
Blitzkrieg Bob
03-18-2007, 03:35 PM
it's cheap insurance while doing the pump and got all that stuff off.
patznu
03-18-2007, 08:59 PM
it's cheap insurance while doing the pump and got all that stuff off.

Hey Bob, sorry to say but, no I did not know of any this about timing belt. I hope all is still ok since the engine was replaced in Sept o6. Any recommendations will be considered though. I must also ask you Bob, Whats up with a now screeching sound? I did notice a leak from steering fluid reservoir/hose area.
Blitzkrieg Bob
03-18-2007, 10:22 PM
Hey Bob, sorry to say but, no I did not know of any this about timing belt. I hope all is still ok since the engine was replaced in Sept o6. Any recommendations will be considered though. I must also ask you Bob, Whats up with a now screeching sound? I did notice a leak from steering fluid reservoir/hose area.

clean it and put some belt dressing or WD-40 on the fan belt.


If the timing belt was serviced, ther ewould be a sticker on the fuse box with the date & mileage.
patznu
03-21-2007, 09:03 PM
clean it and put some belt dressing or WD-40 on the fan belt.


If the timing belt was serviced, ther ewould be a sticker on the fuse box with the date & mileage.

A favor owed cashed in, when I spotted the Ghost behind a used car lot with the hood up night and day. Dealer baffled at engine problem. I told him to thro a price at me ... "500". I made call to the buddy who owes a favor -- also own a bmw or 2 himself and loves to do the body work on european cars, and is capable of most things as time permits the guy. He just happen to have an engine in fair condition- 400/eng 196,000mls 200/labor -- Went back to this dealer with 429 CASH!! Done deal!! Its been running fairly well.



Sorry -- NO STICKER