shogun
02-14-2010, 07:58 AM
I wonder on which BMW this works, anybody knows? Found that on the net:
BMW keyless remotes allow quick entry, locking and trunk-opening. With a few easy steps, you can bypass the fee your dealership may charge to program your system. Your keyless remote can be programmed in minutes, without any past knowledge.
Instructions
Step 1 Close all of the doors on your car, including the trunk and the hood. Remove your key from the ignition.
Step 2 Open the trunk and then get in the car. Close the driver's door and put the key in the ignition.
Step 3 Turn the key one click to the right, then back to the off position. Repeat this process quickly five times, ending in the off position. This process must be completed in 10 seconds. If successful, you will hear a beep.
Step 4 Open and close your driver's door and press any button on your remote to begin the programming process. The red light on your remote will flash on and off.
Step 5 Open your driver's door and get out of the car to close the trunk. Close the driver's door and wait for the keyless remote to emit another short beep. The programming is now complete.
-------------------------------------------------------------
edit, just found
How do you program keyless entry for a BMW 328is?
In: BMW 3-Series, BMW 5-Series
Follow instructions
Close all doors, trunk, and hood.
The alarm must be disarmed. The key needs to be removed from the ignition switch.
Open the trunk and leave it opened.
Open the driver's door and sit in the driver's seat.
Close the driver's door.
Cycle the ignition switch five times between the OFF position and position 2.
The red LED will illuminate continuously, and the siren will chirp once, to indicate that the code learning mode has been started.
The ignition switch cycling must be performed within 10 seconds.
The above sequence must be performed within 45 seconds.
Open the driver's door and remain seated in the driver's seat.
Close the driver's door.
Press and release any button on the remote that you want to register into the module. The status LED will shut off momentarily to indicate that one ID code has been registered.
Open the driver's door and exit the vehicle, leaving the door open.
Close the trunk.
Close the driver's door. The LED will turn off and the siren will chirp twice.
The initialization procedure is now completed.
--------------------------------------------------------
Follow instructions
Close all doors, trunk, and hood.
The alarm must be disarmed. The key needs to be removed from the ignition switch.
Open the trunk and leave it opened.
Open the driver's door and sit in the driver's seat.
Close the driver's door.
Cycle the ignition switch five times between the OFF position and position 2.
The red LED will illuminate continuously, and the siren will chirp once, to indicate that the code learning mode has been started.
The ignition switch cycling must be performed within 10 seconds.
The above sequence must be performed within 45 seconds.
Open the driver's door and remain seated in the driver's seat.
Close the driver's door.
Press and release any button on the remote that you want to register into the module. The status LED will shut off momentarily to indicate that one ID code has been registered.
Open the driver's door and exit the vehicle, leaving the door open.
Close the trunk.
Close the driver's door. The LED will turn off and the siren will chirp twice.
The initialization procedure is now completed.
--------------------------------------------------------
Note: There are comments associated with this question. See the discussion page to add to the conversation.
http://wiki.answers.com/Q/How_do_you_program_keyless_entry_for_a_BMW_328is
------------------------------------
1. Make sure all doors, hood and trunk are closed.
2. Open the trunk door.
3. Open the drivers door and sit in the drivers seat.
4. Close the drivers door.
5. Turn ignition switch to on and off 5 times ending in off.(do not start the car turn to just before starting)
Your alarm light will turn on and the siren on the alarm will chirp to let you know it is ready.
(this can also be used to test if you have the alarm)
6. Open the drivers door stay in the seat close the drivers door.
7. Press any button on the remote. The light will flash to indicate your remote has been programmed.
8. Repeat steps 6 & 7 to program any other remotes, up to 4 remotes a car.
9. To exit program mode open drivers door leave the door open. Close the trunk lid and close the drivers door the
siren should chirp again and the red light will shut off. Test your remotes to make sure they work right.
******Note all the steps from 2 - 5 must be done within 45 seconds. Step 5 must be done within 10 seconds.
http://www.programyourremote.com/classified/DisplayAd.asp?id=85
BMW keyless remotes allow quick entry, locking and trunk-opening. With a few easy steps, you can bypass the fee your dealership may charge to program your system. Your keyless remote can be programmed in minutes, without any past knowledge.
Instructions
Step 1 Close all of the doors on your car, including the trunk and the hood. Remove your key from the ignition.
Step 2 Open the trunk and then get in the car. Close the driver's door and put the key in the ignition.
Step 3 Turn the key one click to the right, then back to the off position. Repeat this process quickly five times, ending in the off position. This process must be completed in 10 seconds. If successful, you will hear a beep.
Step 4 Open and close your driver's door and press any button on your remote to begin the programming process. The red light on your remote will flash on and off.
Step 5 Open your driver's door and get out of the car to close the trunk. Close the driver's door and wait for the keyless remote to emit another short beep. The programming is now complete.
-------------------------------------------------------------
edit, just found
How do you program keyless entry for a BMW 328is?
In: BMW 3-Series, BMW 5-Series
Follow instructions
Close all doors, trunk, and hood.
The alarm must be disarmed. The key needs to be removed from the ignition switch.
Open the trunk and leave it opened.
Open the driver's door and sit in the driver's seat.
Close the driver's door.
Cycle the ignition switch five times between the OFF position and position 2.
The red LED will illuminate continuously, and the siren will chirp once, to indicate that the code learning mode has been started.
The ignition switch cycling must be performed within 10 seconds.
The above sequence must be performed within 45 seconds.
Open the driver's door and remain seated in the driver's seat.
Close the driver's door.
Press and release any button on the remote that you want to register into the module. The status LED will shut off momentarily to indicate that one ID code has been registered.
Open the driver's door and exit the vehicle, leaving the door open.
Close the trunk.
Close the driver's door. The LED will turn off and the siren will chirp twice.
The initialization procedure is now completed.
--------------------------------------------------------
Follow instructions
Close all doors, trunk, and hood.
The alarm must be disarmed. The key needs to be removed from the ignition switch.
Open the trunk and leave it opened.
Open the driver's door and sit in the driver's seat.
Close the driver's door.
Cycle the ignition switch five times between the OFF position and position 2.
The red LED will illuminate continuously, and the siren will chirp once, to indicate that the code learning mode has been started.
The ignition switch cycling must be performed within 10 seconds.
The above sequence must be performed within 45 seconds.
Open the driver's door and remain seated in the driver's seat.
Close the driver's door.
Press and release any button on the remote that you want to register into the module. The status LED will shut off momentarily to indicate that one ID code has been registered.
Open the driver's door and exit the vehicle, leaving the door open.
Close the trunk.
Close the driver's door. The LED will turn off and the siren will chirp twice.
The initialization procedure is now completed.
--------------------------------------------------------
Note: There are comments associated with this question. See the discussion page to add to the conversation.
http://wiki.answers.com/Q/How_do_you_program_keyless_entry_for_a_BMW_328is
------------------------------------
1. Make sure all doors, hood and trunk are closed.
2. Open the trunk door.
3. Open the drivers door and sit in the drivers seat.
4. Close the drivers door.
5. Turn ignition switch to on and off 5 times ending in off.(do not start the car turn to just before starting)
Your alarm light will turn on and the siren on the alarm will chirp to let you know it is ready.
(this can also be used to test if you have the alarm)
6. Open the drivers door stay in the seat close the drivers door.
7. Press any button on the remote. The light will flash to indicate your remote has been programmed.
8. Repeat steps 6 & 7 to program any other remotes, up to 4 remotes a car.
9. To exit program mode open drivers door leave the door open. Close the trunk lid and close the drivers door the
siren should chirp again and the red light will shut off. Test your remotes to make sure they work right.
******Note all the steps from 2 - 5 must be done within 45 seconds. Step 5 must be done within 10 seconds.
http://www.programyourremote.com/classified/DisplayAd.asp?id=85