1995 530i m60 (oxygen sensors)

[ethirty4HTX]

Hello everyone, I've ran into a problem that's an easy fix but part is no where to be found. The connection to plug in my oxygen sensors (http://motors.shop.ebay.com/i.html?_nkw=o2+sensor) has been cut and there no way to connect the oxygen sensors to the engine. Basically my two sensors are in where they're suppose to be but no connection to plug them into. I'm looking for just that connection if anyone has a engine wiring harness to my car that isn't complete and would just cut both of the oxygen sensor connections with the most wire connected to them that would be awesome. If anyone knows any way around this please let me know also. I'm currently searching for e34's with my engine in them at junk yards but I've just started and haven't had any luck. Everything is appreciated!
Thanks.

[shogun]

Do you have the round plugs like this? http://img167.imageshack.us/img167/11/oxysensortesterbs3.png that is my self made oxy sensor tester, made with a kit from Jaycar Australia
https://www.youtube.com/watch?gl=DE&v=K8miz_1aHYw&hl=de&feature=channel_page
Here I posted the info where to buy in Australia http://www.bimmerboard.com/forums/posts/607249
CAT. NO. KC5195 Mixture Display Kit For Fuel Injected Cars http://wp1016621.server-he.de/fotost/f01358/06.jpg
Refer: Silicon Chip November 1995 This very simple kit will allow you to monitor the fuel mixtures being run by your car. This type of sensor is also known as an E.G.O. (exhaust, gas, oxygen) monitor. You can use it as a tuning tool, to help in vehicle modification or simply to see the behaviour of the engine control module. Indication is via 10 LEDs to show mixtures rich, lean and normal. The circuit connects to the EGO sensor mounted in the exhaust manifold and the cars battery. PCB, LEDs and components supplied.

oxy sensor plug housing 61131718057 (this part is NOT shown in the ETK, BMW internal use only)
round pin connector d 2,5 0,5 – 1,0 61131376202
http://www.ecstuning.com/Search/SiteSearch/61131376202/

oxy sensor plug housing cable loom 61131718058 (this part is NOT shown in the ETK, BMW internal use only)
round pin connector d 2,5 0,5 – 1,5 61131376191

When I ordered it from my dealer in Germany, the German spec was
Lambdasonde Steckergehäuse 61131718 057
Rundsteckhülse d 2,5 0,5 – 1,0 61131376202

Lambdasonde Steckergehäuse Kabelbaum 61131718058
Rundstecker d 2,5 0,5 – 1,5 61131376191
http://www.ecstuning.com/Search/W211/ES164438

In case these are not the ones you are looking for, see here under plugs engine, plugs chassis http://bmwfans.info/

[ethirty4HTX]

Wow man I preciate all this info! But I just ended up finding a wiring harness for cheap on ebay. $80 was something I wanted to spend but I wasn't finding anything. All I gotta do now is wait for the harness, connect the plugs, and I should be good. Thanks again though!!

[ethirty4HTX]

Didnt*

[632 Regal]

I'm not sure if it matters but the plug is directional. Not sure what happens if hooked up in reverse.

[Rustam]

Do you have the round plugs like this? http://img167.imageshack.us/img167/11/oxysensortesterbs3.png that is my self made oxy sensor tester, made with a kit from Jaycar Australia
https://www.youtube.com/watch?gl=DE&v=K8miz_1aHYw&hl=de&feature=channel_page
Here I posted the info where to buy in Australia http://www.bimmerboard.com/forums/posts/607249
CAT. NO. KC5195 Mixture Display Kit For Fuel Injected Cars http://wp1016621.server-he.de/fotost/f01358/06.jpg
Refer: Silicon Chip November 1995 This very simple kit will allow you to monitor the fuel mixtures being run by your car. This type of sensor is also known as an E.G.O. (exhaust, gas, oxygen) monitor. You can use it as a tuning tool, to help in vehicle modification or simply to see the behaviour of the engine control module. Indication is via 10 LEDs to show mixtures rich, lean and normal. The circuit connects to the EGO sensor mounted in the exhaust manifold and the cars battery. PCB, LEDs and components supplied.

oxy sensor plug housing 61131718057 (this part is NOT shown in the ETK, BMW internal use only)
round pin connector d 2,5 0,5 – 1,0 61131376202
http://www.ecstuning.com/Search/SiteSearch/61131376202/

oxy sensor plug housing cable loom 61131718058 (this part is NOT shown in the ETK, BMW internal use only)
round pin connector d 2,5 0,5 – 1,5 61131376191

When I ordered it from my dealer in Germany, the German spec was
Lambdasonde Steckergehäuse 61131718 057
Rundsteckhülse d 2,5 0,5 – 1,0 61131376202

Lambdasonde Steckergehäuse Kabelbaum 61131718058
Rundstecker d 2,5 0,5 – 1,5 61131376191

In case these are not the ones you are looking for, see here under plugs engine, plugs chassis http://bmwfans.info/


http://www.ecstuning.com/Search/W211/ES164438/

Thank you, for this information, Shogun.