GO FISHING, use SLABSAUCE Fishing Attractant
Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: Hubcentric Ring Question

  1. #1
    Join Date
    Sep 2005
    Location
    NJ
    Posts
    1,089

    Default Hubcentric Ring Question

    Alright, since I could not figure out what was causing my slight vibration and weird "whurring" noise coming from my new rims, I decided to buy new rear tires to hopefully fix the problems. I have a question. Are these the correct rings you are supposed to use with e39 rims?? http://cgi.ebay.com/ebaymotors/BMW-H...spagenameZWDVW (These are the rings that are currently installed with my rims). Is the ring supposed to cover the entire hub, or just the extra 2 mm or so?? My rings do not cover the entire hub. Once again, is there any possibiblty that I'm rubbing against the control arm?? There is only about 1 finger width of space between the tire and control arm (I think that's what it is). Thanks for your time guys.

  2. #2
    Join Date
    Dec 2003
    Location
    Eastern Tennessee USi
    Posts
    14,843

    Default

    The rings look right but im not sure without seeing them on the car and against the wheel, you might want plastic ones anyways cause the aluminum sometimes welds itself to the wheels.

    The 1 finger width is about right.
    95 E34 530I V2.37
    ===========
    Those who make peaceful revolution impossible will make violent revolution inevitable.

    John F. Kennedy

  3. #3
    Join Date
    Sep 2005
    Location
    NJ
    Posts
    1,089

    Default

    I was told to get aluminum ones because the plastic ones become brittle and crack.

  4. #4
    Join Date
    Dec 2003
    Location
    Eastern Tennessee USi
    Posts
    14,843

    Default

    choose your poisen.

    Id rather get a few sets and install fresh vs chiseling the old ring off my wheels.
    95 E34 530I V2.37
    ===========
    Those who make peaceful revolution impossible will make violent revolution inevitable.

    John F. Kennedy

  5. #5
    Join Date
    Sep 2005
    Location
    NJ
    Posts
    1,089

    Default

    What kind do you have??? I would like to get new rings before the tires come to hopefully solve the problem for good. Do you have any problems with your rims? What size are your tires?? -Thanks

  6. #6
    Join Date
    Jun 2004
    Location
    Bay Area, CA
    Posts
    1,825

    Default

    Quote Originally Posted by E34 530
    What kind do you have??? I would like to get new rings before the tires come to hopefully solve the problem for good. Do you have any problems with your rims? What size are your tires?? -Thanks

    I myself have plastic ones.

    www.KaRealtySF.com
    Build Date: 05-1995 /Engine: m50tu /Automatic Transmission /ABS /NO ASC /Open Differential /EAT Chip

  7. #7
    Join Date
    Sep 2005
    Location
    NJ
    Posts
    1,089

    Default

    Liquidtiger, I know you originally had a lot of problems with rubbing and whatnot. Where did you get your rings? Also, I am using the same lug nuts that were used with the stock 15 inch basketweaves. Could this be a problem?? -Thanks

  8. #8
    Join Date
    Jun 2004
    Location
    Bay Area, CA
    Posts
    1,825

    Default

    You'll be fine with the OEM lug nuts.

    My rings were provided by Pete. But my ring diameters are different.

    If you call tirerack, they do sell the more common ring used for bmw's the e39 hub size to the rest of bmw line hub size.

    www.KaRealtySF.com
    Build Date: 05-1995 /Engine: m50tu /Automatic Transmission /ABS /NO ASC /Open Differential /EAT Chip

  9. #9
    Join Date
    Sep 2005
    Location
    NJ
    Posts
    1,089

    Default

    632 regal, can you tell me what centric rings you are running. Do you also have e39 rims on your car? Can you tell me where and how much your rings cost you. -Thanks

  10. #10
    Join Date
    Jul 2004
    Location
    Vancleave, MS
    Posts
    629

    Default call tirerack... about $40 for 4 aluminium ones...

    ... think the part # is like t790 or something... and think it's like 72.4 to 74.. but if you tell them it's to put E39 wheels on an E34 they'll be able to figure it out for you.... the metal ones will rest into the wheel, then put the wheel on the hub... if you put the ring on the hub and press it flush, it'll miss the wheel and the hub is deeper than the portion of the wheel that sits on the hub... (thus put the ring onto the wheel, then carefully put the wheel onto the hub... -Rob.

Page 1 of 2 12 LastLast

Similar Threads

  1. Hubcentric ring installation
    By Derek A. in forum 5 Series BMW
    Replies: 1
    Last Post: 07-31-2006, 10:54 AM
  2. hubcentric ring for E39 wheel to go on my E34?
    By pismojeff in forum 5 Series BMW
    Replies: 1
    Last Post: 12-18-2004, 04:44 PM
  3. Hubcentric Question
    By Unregistered in forum 5 Series BMW
    Replies: 6
    Last Post: 04-07-2004, 06:40 PM
  4. problems on hubcentric ring
    By kamote in forum 5 Series BMW
    Replies: 7
    Last Post: 02-29-2004, 10:59 PM
  5. Hub-centric Ring Question
    By JR'Z 525 in forum 5 Series BMW
    Replies: 9
    Last Post: 02-13-2004, 01:42 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •