GO FISHING, use SLABSAUCE Fishing Attractant
Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

Thread: thermostat housing gasket - silicon or no?

  1. #11
    Join Date
    Nov 2005
    Location
    Southern NH
    Posts
    47

    Default

    Quote Originally Posted by romeox929
    I don't know when they started producing m50's for 525's, but I'm positive I have a M50.
    OK, you're right (of course - it's your car) The last of the M20's was produced in August 1990. So I assume that yours was built post September '90.

    And sure enough yours does apparently have a paper gasket rather than the profile gasket (also shown in the below drawing). I would definitely use some permagasket compound or something similar.

    http://www.realoem.com/bmw/showparts...03&hg=11&fg=35
    Fred W
    (oo 00 oo)

    95 325i
    94 540iA
    97 Z3 2.8

  2. #12
    Join Date
    Dec 2003
    Location
    Eastern Tennessee USi
    Posts
    14,843

    Default

    Bill R like Hylomar.
    95 E34 530I V2.37
    ===========
    Those who make peaceful revolution impossible will make violent revolution inevitable.

    John F. Kennedy

  3. #13
    Join Date
    Jan 2004
    Location
    Thunder Bay, Ontario
    Posts
    2,538

    Default

    Quote Originally Posted by 632 Regal
    Bill R like Hylomar.
    I'm through half a tube of the $hit putting my car back together (none on the head gasket )

    Dave M

    10/90 Build 525im, 630,000+km, Eibach/Sachs, Engine Rebuild
    *RIP Oskar the DOG *

  4. #14
    Join Date
    Dec 2005
    Location
    Independence Oregon USA - pop. 6000
    Posts
    296

    Default

    After doing the waterpump and thermostat housing replacement on my M50 '93 525iT I would (and did) go with no goop at all. The M50 is all compressible rubber rings. Just clean mating surfaces well. Not leaking yet...
    Tom

  5. #15
    Join Date
    Jan 2004
    Location
    Nashville, TN
    Posts
    982

    Default

    I thin coat of RTV on the metal not sealing surfaces will help to prevent leaks down the road, especially of there is pitting present on the aluminum.

    The real early M50's used a paper gasket. After that its all profile gaskets and o rings.
    Derek A.
    90 535i 5 Speed - Style 5 17"

  6. #16
    Join Date
    Oct 2004
    Posts
    3,395

    Default

    No RTV. Many an engine is destroyed by some idiot goobering it up with the stuff. It has its uses, but the tstat cover is not one of them. Use a scotch brite pad or a new razor blade to clean the aluminum, the rubber profile gasket and tstat O ring prevent leaking, but things need to be flush.

    These engines only need a TINY dot of RTV at gasket junctions between covers (ie - pan/block/lower timing cover gets a dot on each side on the outboard side of the gasket during a pan gasket job). For some reason, people think that RTV can universally replace the use of an actual gasket. To make matters worse, they put more than a dot on the motor to form some kind of seal that won't leak, and neglect the fact that just as much squeezes in as what squeezes out. The stuff solidifies and turns into strings of goob, which proceed to clog tiny and necessary coolant passages, overheating the car and trashing the head. Or it can get in the oil (pan gasket scenario) and lunch the bottom end.

    So, no RTV. And I doubt you'll need hylomar in this situation, either. Clean, bolt, and go. If you still have leaks, then there's a pitted or damaged surface that merits replacement, anyway.

    best, whit

Page 2 of 2 FirstFirst 12

Similar Threads

  1. Thermostat housing leak m50
    By colo525i in forum 5 Series BMW
    Replies: 2
    Last Post: 08-04-2009, 05:02 PM
  2. Question on M50 alu thermostat housing gasket
    By colo525i in forum 5 Series BMW
    Replies: 4
    Last Post: 12-30-2006, 08:46 AM
  3. M60 - metal thermostat housing ?
    By Super90 in forum 5 Series BMW
    Replies: 4
    Last Post: 02-01-2006, 11:57 AM
  4. Bad oil filter Housing gasket & Profile Gasket
    By mbogosia in forum 5 Series BMW
    Replies: 8
    Last Post: 01-17-2006, 09:33 AM
  5. 525 aluminium thermostat housing
    By shogun in forum 5 Series BMW
    Replies: 1
    Last Post: 12-15-2005, 03:48 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •